HomeMy WebLinkAbout2200-20UNDERGROUND
TELEPHONE SPECIFICATIONS
1. All conduits bends to have minimum radius in feet equal to di.. • :,iter of conduit in inches.
2" diameter = 24" radius, etc.
2. No conduit run to have over two 90° bends, if necessary to have over two 90° bends,
insert accessible pull box in run. Contact Telephone engineer for pull box sizing.
3. All conduit shall be left clean, dry, and free of debris or other obstructions. A pull line
equivalent to No. 14 AWG -3/16" polpropylene or conduit measuring tape.
4. Approved plastic is specified in underground construction. Condulets, plumber's fitting,
water and gas pipes must not be used.
5. Conduit terminated on a pole must be turned up V above finish grade, in the opposite
quadrant from any power services. (See detail of pole for termination).
6. Conduit placed in same trench with power conduit must be separated by not less than
12" of well packed dirt or 3" of concrete, and have not less than 30" of cover.
7. Approved Plastic Conduit PTS 66 2"
P.V.C. Sch. 40 PTS1366 PTS 77 4"
A.B.S. "D.B." P&C Duct PUBLIC STREET
PRIVATE, PROPERTY
8. The Telephone Company reserves the right to refuse to use conduitthat deviated from
plans and specifications.
9. In runs of 400 ft. or over, bends having radii of 80 ft. or less must be concrete encased.
In changes of grade 20% (11.3 degrees) or more the conduit must be encased in
concrete.
TELEPHONE CONDUIT
MIN. 12" BACKFILL
OR 3" CONCRETE
POWER CONDUIT
TYPICAL f
ABOVE GRADE t
POLE FOOTINGI
T SERVICE
t 'CONDUITS
' k -PROPERTY
LINE
r1 ion
PACIFIC BELL REQUIREMENTS ARE GENERALLY LIMITED TO ENTRANCE CONDUIT,
BACKBOARD(S) UFER GROUND AND A CONDUIT(S) TO EACH TENANT SPACE.
ANY REQUIREMENTS FOR TERMINAL EQUIPMENT (PBX, KEY TELEPHONE, ECT.)
WILL BE PROVIDED BY VENDORS OF THE TERMINAL EQUIPMENT.
1. ALL CONDUIT RUNS WILL BE LIMITED TO (2) 90 SWEEPS EQUIPPED WITH
PULL LINES.
TELEPHONE BACKBOARD — SIZE AS INDICATED. ALL CONDUITS
TO TERMINATE 2" ABOVE FLOOR OR 6" BELOW CEILING.
110-120 V DOUBLE DUPLEX RECEPTABLE ON A SEPARATE CIRCUIT
LOCATED AS INDICATED
A CONCRETE ENCASED ELECTRODE (UFER) — COMMON WITH POWER
SERVICE GROUND ADJACENT TO BACKBOARD. PER NEC ARTICLE
250.
511 t I'UWtK & i tLtl'F1UNt StKVI(:t NU I t5
SOUTHERN CALIFORNIA EDISON COMPANY (S.C.E.)
PACIFIC BELL TELEPHONE (P.B.)
@-4" C.O. FOR HIGH VOLTAGE SERVICE. VERIFY THE
LOCATION AND ROUTING. HIGH VOLTAGE CONDUIT
SHALL BE 48" DEEP WITH 3" CONCRETE FOR THE
ENCASEMENT.
@—TRANSFORMER SLAB BOX WITH TRAFFIC GUARDS
PER S.C.E. REQUIREMENTS, VERIFY SIZE, LOCATION
AND ORIENTATION WITH S.C.E.
@-4" C.O. FOR SECONDARY FROM THE TRANSFORMER
TO THE MAIN SWITCHGEAR. (1)—r C.O. FOR EACH
400A OF SERVICE. VERIFY ROUTING WITH S.C.E.
AND ROUTE TO CLEAR STRUCTURAL FOOTINGS.
@—STUB OUT AND TERMINATE PER S.C.E. REQUIREMENTS.
VERIFY LOCATION OF HIGH VOLTAGE SERVICE POINT
PRIOR TO BIDDING AND INCLUDE ALL COSTS IN
THE BID.
—STUB OUT AND TERMINATE PER P.B. REQUIREMENTS.
VERIFY LOCATION OF TELEPHONE SERVICE POINT
PRIOR TO BIDDING AND INCLUDE ALL COSTS IN
THE BID.
@—PULLBOX NTH TRAFFIC COVER PER TELEPHONE
COMPANY'S REQUIREMENTS. SIZE AS INDICATED;
VERIFY LOCATION, TYPICAL.
(@—ROUTE TO THE MAIN SERVICE ENTRANCE,
-- ALL UTILITY SERVICES SHALL BE VERIFIED WITH
THE UTILITY COMPANIES PRIOR TO BIDDING AND
ALL RESULTING COSTS SHALL BE INCLUDED IN
THE BID.
PACIFIC BELL
TELEPHONE LAYOUT FOR:
ci\,/Rl
PREPARED,BY:D�
��o�i; lam, i A L GR � �1
*IMPORTA T -=- NO CHANGES WITHOUT AUT ORIZATION
OF PERSON RESPONSIBLE FOR LAYOUT.
DATE:
1
PACIFIC13BELL-
IMPORTANT
BEFORE TELEPHONE ENTRANCE FACILITIES CAN BE
PROVIDED TO: PAIZk'- LjAAPi moi_. Lt.
ALL DEVELOPER PROVIDED SUPPORTING STRUCTURES
MUST BE IN PLACE AND INSPECTED 30 DAYS PRIOR TO
CABLE PLACEMENT.
I.E., ENTRANCE CONDUIT, PULL LINES, BACKBOARDS, PULL
BOXES, MANHOLES, ELECTRICAL OUTLETS, PENETRATIONS
OF CONCRETE, FIRE RATED WALLS, INTERIOR CONDUITS,
GROUND, ETC.
AT START OF CONSTRUCTION CALL( 7 01�
FOR JOB SITE MEET AND INSPECTION CARD. ACTUAL
INSTALLATION OF TELEPHONE ACCESS LINES WILL
FOLLOW ENTRANCE FACILITY PLACEMENT.
DATE
Underground Service Alert
Catt:TOLL FREE
800
422w4133
TWO WORKING DAYS BEFORE YOU DIG
RECORD DRAWING I;
I AMARIND AVENUE
The information on this drawing is obtakW from others and
must be verified in the field by anyorw prior to use or
construction,_- _Co��U/tome _ _ Js�not responsible for
underground facility locations or demtims. All above ground
facilities can be readily seen and verified by the pares that
end to use sante. 'I,- -I/"--
RC1) -4''C,0.
EXISTING POWER POLE
TO SLOVER AVENUE
SERVICE
POINT, ROUTE ALONG
SERVICE DRIVE,
SLOVER AVENU
( IN FEET )
I inch = 50 ft.
SliT 20 OF a6 2.6
4
�E 120'—�
2O—ACTUAL
INSTALLATION OF
ALL UTILITY SERVICES
SHALL BE ACCORDING TO
THE FINAL ENGINEERED
SCALE
UTILITY
ON THE
COMPANY PLANS.
NOTE SHEET.
SEE THE "UTILITY NOTES'
SERVICE DRIVE DETAIL
M r c
PACIFIC BELL
TELEPHONE LAYOUT FOR:
ci\,/Rl
PREPARED,BY:D�
��o�i; lam, i A L GR � �1
*IMPORTA T -=- NO CHANGES WITHOUT AUT ORIZATION
OF PERSON RESPONSIBLE FOR LAYOUT.
DATE:
1
PACIFIC13BELL-
IMPORTANT
BEFORE TELEPHONE ENTRANCE FACILITIES CAN BE
PROVIDED TO: PAIZk'- LjAAPi moi_. Lt.
ALL DEVELOPER PROVIDED SUPPORTING STRUCTURES
MUST BE IN PLACE AND INSPECTED 30 DAYS PRIOR TO
CABLE PLACEMENT.
I.E., ENTRANCE CONDUIT, PULL LINES, BACKBOARDS, PULL
BOXES, MANHOLES, ELECTRICAL OUTLETS, PENETRATIONS
OF CONCRETE, FIRE RATED WALLS, INTERIOR CONDUITS,
GROUND, ETC.
AT START OF CONSTRUCTION CALL( 7 01�
FOR JOB SITE MEET AND INSPECTION CARD. ACTUAL
INSTALLATION OF TELEPHONE ACCESS LINES WILL
FOLLOW ENTRANCE FACILITY PLACEMENT.
DATE
Underground Service Alert
Catt:TOLL FREE
800
422w4133
TWO WORKING DAYS BEFORE YOU DIG
RECORD DRAWING I;
I AMARIND AVENUE
The information on this drawing is obtakW from others and
must be verified in the field by anyorw prior to use or
construction,_- _Co��U/tome _ _ Js�not responsible for
underground facility locations or demtims. All above ground
facilities can be readily seen and verified by the pares that
end to use sante. 'I,- -I/"--
RC1) -4''C,0.
EXISTING POWER POLE
TO SLOVER AVENUE
SERVICE
POINT, ROUTE ALONG
SERVICE DRIVE,
SLOVER AVENU
( IN FEET )
I inch = 50 ft.
SliT 20 OF a6 2.6
4